| Internet-Draft | YANG Data Model for SRv6 | March 2024 |
| Raza, et al. | Expires 5 September 2024 | [Page] |
This document describes a YANG data model for Segment Routing IPv6 (SRv6) base. The model serves as a base framework for configuring and managing an SRv6 subsystem and expected to be augmented by other SRv6 technology models accordingly. Additionally, this document also specifies the model for the SRv6 Static application.¶
The YANG modules in this document conform to the Network Management Datastore Architecture (NMDA).¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 5 September 2024.¶
Copyright (c) 2024 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶
The Network Configuration Protocol (NETCONF) [RFC6241] is one of the network management protocols that defines mechanisms to manage network devices. YANG [RFC6020] is a modular language that represents data structures in an XML tree format, and is used as a data modeling language for the NETCONF.¶
Segment Routing (SR), as defined in [RFC8402], leverages the source routing paradigm where a node steers a packet through an ordered list of instructions, called segments. SR, thus, allows enforcing a flow through any topological path and/or service chain while maintaining per-flow state only at the ingress nodes to the SR domain. When applied to ipv6 data-plane (i.e. SRv6), SR requires a type of routing header (SRH) in an IPv6 packet that is used to encode an ordered list of IPv6 addresses (SIDs). The active segment is indicated by the Destination Address of the packet, and the next segment is indicated by a pointer in the SRH [RFC8754]. The various functions and behaviors corresponding to network programming using SRv6 are specified in [RFC8986].¶
This document introduces a YANG data model for base SRv6 that would serve as a base framework for configuring and managing an SRv6 subsystem. As needed, other SRv6 technology models (e.g. ISIS, OSPFv3, BGP, EVPN, Service Chaining) may augment this model. Furthermore, to illustrate basic behaviors as captured in [RFC8986], this document also specifies a YANG model for the SRv6-Static application.¶
The model currently defines the following constructs that are used for managing SRv6:¶
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.¶
This document defines following three new YANG modules:¶
ietf-srv6-types: defines common and basic types related to SRv6¶
ietf-srv6-base: specifies management model for SRv6 base constructs (locator, SIDs, etc.)¶
ietf-srv6-static: specifies management model for SRv6-static application¶
The modeling in this document complies with the Network Management Datastore Architecture (NMDA) defined in [RFC8342]. The operational state data is combined with the associated configuration data in the same hierarchy [RFC8407]. When protocol states are retrieved from the NMDA operational state datastore, the returned states cover all "config true" (rw) and "config false" (ro) nodes defined in the schema.¶
In this document, when a simplified graphical representation of YANG model is presented in a tree diagram, the meaning of the symbols in these tree diagrams is defined in [RFC8340].¶
SRv6 common types and definitions are defined in the new module "ietf-srv6-types". The main types defined in this module include:¶
srv6-sid: SRv6 SID¶
srv6-func-value: Typedef for FUNC value in an SRv6 SID¶
srv6-func-value-reserved-type: Enum (list) of "reserved" FUNC opcode¶
srv6-endpoint-type: SRv6 Endpoint behaviors [RFC8986] identity type¶
srv6-headend-type: SRv6 Headend behaviors [RFC8986] identity type¶
srv6-security-type: SRv6 Security rules identity type¶
The corresponding YANG specification for this module is captured in Section 5.1.¶
The base SRv6 model is specified in ietf-srv6-base module. This module augments "/rt:routing:/sr:segment-routing" [RFC9020] and specifies the configuration, operational state, and notification events that are required to manage the base SRv6.¶
The corresponding YANG specification for this module is captured in Section 5.2.¶
The module defines some fundamental items required to configure an SRv6 network:¶
SRv6 Enablement: Enable Segment-Routing SRv6 feature¶
Encapsulation Parameters: Provide encapsulation related parameters (such as source-address, hop-limit, and traffic-class) to be used when performing T.Encap* operation.¶
Locator(s) Specification: SRv6 locator is a fundamental construct for an SRv6 network. This is the construct from which SID (function values) are allocated that on the local box, and advertised to and used by remote nodes for reachability. A locator is identified by a name and has associated prefix and IGP algorithm. It can be configured as an anycast locator. It is possible to have more than one locator on a node (e.g. locator per algorithm, anycast and non-anycast locators, etc.).¶
Following is a simplified graphical tree representation of the data model for SRv6 base configuration¶
module: ietf-srv6-base
augment /rt:routing/sr:segment-routing:
+--rw srv6
+--rw enable? boolean
+--rw encapsulation
| +--rw source-address? inet:ipv6-address
| +--rw hop-limit
| | +--rw value? uint8
| | +--rw propagate? boolean
| +--rw traffic-class
| +--rw value? uint8
| +--rw propagate? boolean
+--rw locators
+--rw locator* [name]
+--rw name string
+--rw enable? boolean
+--rw prefix
| +--rw address inet:ipv6-address
| +--rw length srv6-types:srv6-locator-len
+--rw algorithm? uint32
+--rw anycast? boolean
As per NMDA model, the state related to configuration items specified in above section Section 3.3.1 can be retrieved from the same tree. This section defines other operational state items related to SRv6 base.¶
The operational state corresponding to the SRv6 base includes:¶
node capabilities: provides information on the node (hardware) capabilities and support regarding various SRv6 aspects and features including endpoint behaviors, headend behaviors, security rules, counter/stats support, and other SRv6 parameters that need to be signaled in an SRv6 network by the protocols.¶
locator: provides information related to a locator. The information includes locator operational state, and state of address conflict with any ipv6 address configured on local interfaces etc.¶
local-sid: provides information related to local-SIDs allocated and/or installed on the node. This includes two types of information:¶
Following is a simplified graphical tree representation of the data model for the SRv6 operational state (for read-only items):¶
module: ietf-srv6-base
augment /rt:routing/sr:segment-routing:
+--rw srv6
+--rw locators
| +--rw locator* [name]
| +--rw name string
| +--ro operational-status? srv6-types:srv6-status-type
| +--ro is-in-address-conflict? boolean
+--ro node-capabilities
| +--ro end-behavior* [type]
| | +--ro type identityref
| | +--ro supported boolean
| +--ro headend-behavior* [type]
| | +--ro type identityref
| | +--ro supported boolean
| +--ro msd
| | +--ro max-sl? uint8
| | +--ro max-end-pop? uint8
| | +--ro max-h_encap? uint8
| | +--ro max-end_d? uint8
| +--ro security-rule* [type]
| | +--ro type identityref
| | +--ro supported boolean
| +--ro counters* [type]
| +--ro type identityref
| +--ro supported boolean
+--ro local-sids
+--ro counters
| +--ro cnt-3
| +--ro in-pkts? yang:counter64
| +--ro in-octets? yang:counter64
+--ro local-sid* [sid]
+--ro sid srv6-types:srv6-sid
+--ro locator? -> /rt:routing/sr:segment-routing/srv6:srv6/locators/locator/name
+--ro is-reserved? boolean
+--ro end-behavior-type? identityref
+--ro alloc-type? srv6-types:sid-alloc-type
+--ro owner* [type instance]
| +--ro type identityref
| +--ro instance string
| +--ro is-winner? boolean
+--ro forwarding
| +--ro is-installed? boolean
| +--ro next-hop-type? srv6-types:srv6-nexthop-type
| +--ro paths
| +--ro path* [path-index]
| +--ro path-index uint8
| +--ro l2
| | +--ro interface? if:interface-ref
| +--ro l3
| | +--ro interface? if:interface-ref
| | +--ro next-hop? inet:ip-address
| | +--ro weight? uint32
| | +--ro role? enumeration
| | +--ro backup-path-index? uint8
| +--ro (encap-type)?
| +--:(srv6)
| | +--ro out-sid* [sid]
| | +--ro sid srv6-types:srv6-sid
| +--:(mpls)
| +--ro out-label* [label]
| +--ro label rt-types:mpls-label
+--ro counters
+--ro cnt-1
+--ro in-pkts? yang:counter64
+--ro in-octets? yang:counter64
This model defines a list of notifications to inform an operator of important events detected during the SRv6 operation. These events include events related to:¶
Following is a simplified graphical tree representation of the data model for SRv6 notifications:¶
module: ietf-srv6-base
notifications:
+---n srv6-locator-status-event
| +--ro operational-status? srv6-types:srv6-status-type
| +--ro locator? -> /rt:routing/sr:segment-routing/srv6:srv6/locators/locator/name
+---n srv6-sid-collision-event
+--ro sid? srv6-types:srv6-sid
+--ro existing
| +--ro end-behavior-type? identityref
+--ro requested
+--ro end-behavior-type? identityref
SRv6-Static application allows a user to specify SRv6 local SIDs and program them in the forwarding plane. The SRv6-Static model is captured in the ietf-srv6-static module.¶
The associated YANG specification for this module is captured in Section 5.3.¶
The SRv6-Static configuration augments the SRv6-base locator tree "/rt:routing/sr:segment-routing/srv6:srv6/srv6:locators/srv6:locator"¶
Following are salient features of the SRv6-Static config model:¶
Allows static (explicit) configuration for local-SIDs under a given locator.¶
Given that entry is scoped under a locator, the key for each entry is "function" value.¶
A user must also specify end-behavior type (End*) associated with the entry.¶
A user must also specify behavior-specific data with each entry. For example, for any end behavior requiring a table lookup, a lookup-table need be provided. Similarly, for any end behavior with forwarding next-hops need to specify next-hop information. The example of former include End, End.T, End.DT4, End.DT6, and End.DT46, whereas example of later include End.X, End.DX4, End.DX6, End.B6, End.BM etc.¶
Each local-SID entry has zero or more forwarding paths specified.¶
A forwarding path has next-hop type that depends on the end behavior, and could be either ipv6, or ipv4, or mpls, or l2 type. For example, End.X, End.DX4, End.DX6, End.B6, End.BM, and End.DX2 will have ipv6, ipv4, ipv6, ipv6, mpls, and l2 next-hop types respectively¶
For each forwarding next-hop type, the appropriate path attributes are to be specified as well. For L2 type, the only other information required is the L2 interface name. Whereas for L3 (ipv6, ipv4, mpls) types, the information includes L3 interface name, next-hop IP address, weight, and protection information.¶
Depending on the end behavior type, a forwarding path may have either MPLS or SRv6 encapsulation -- i.e., Stack of out-labels or Stack of SRv6 out-SIDs. The example of former is End.BM and example of later include the rest (End.X, End.DX4, End.DX6, End.B6 etc.).¶
Following is a simplified graphical tree representation of the data model for SRv6 Static configuration¶
module: ietf-srv6-static
augment /rt:routing/sr:segment-routing/srv6:srv6/srv6:locators/srv6:locator:
+--rw static
+--rw local-sids
+--rw sid* [function]
+--rw function srv6-types:srv6-func-value
+--rw end-behavior-type identityref
+--rw end
+--rw end_psp
+--rw end_usp
+--rw end_psp_usp
+--rw end_usd
+--rw end_psp_usd
+--rw end_usp_usd
+--rw end_psp_usp_usd
+--rw end-t
| +--rw lookup-table-ipv6 srv6-types:table-id
+--rw end-t_psp
| +--rw lookup-table-ipv6 srv6-types:table-id
+--rw end-t_usp
| +--rw lookup-table-ipv6 srv6-types:table-id
+--rw end-t_psp_usp
| +--rw lookup-table-ipv6 srv6-types:table-id
+--rw end-t_usd
| +--rw lookup-table-ipv6 srv6-types:table-id
+--rw end-t_psp_usd
| +--rw lookup-table-ipv6 srv6-types:table-id
+--rw end-t_usp_usd
| +--rw lookup-table-ipv6 srv6-types:table-id
+--rw end-t_psp_usp_usd
| +--rw lookup-table-ipv6 srv6-types:table-id
+--rw end-x
| +--rw protected? boolean
| +--rw paths
| +--rw path* [path-index]
| +--rw path-index uint8
| +--rw interface? if:interface-ref
| +--rw next-hop? inet:ipv6-address
| +--rw table? srv6-types:table-id
| +--rw weight? uint32
| +--rw role? enumeration
| +--rw backup-path-index? uint8
| +--rw sid-list
| +--rw out-sid* [sid]
| +--rw sid srv6-types:srv6-sid
+--rw end-x_psp
| +--rw protected? boolean
| +--rw paths
| +--rw path* [path-index]
| +--rw path-index uint8
| +--rw interface? if:interface-ref
| +--rw next-hop? inet:ipv6-address
| +--rw table? srv6-types:table-id
| +--rw weight? uint32
| +--rw role? enumeration
| +--rw backup-path-index? uint8
| +--rw sid-list
| +--rw out-sid* [sid]
| +--rw sid srv6-types:srv6-sid
+--rw end-x_usp
| +--rw protected? boolean
| +--rw paths
| +--rw path* [path-index]
| +--rw path-index uint8
| +--rw interface? if:interface-ref
| +--rw next-hop? inet:ipv6-address
| +--rw table? srv6-types:table-id
| +--rw weight? uint32
| +--rw role? enumeration
| +--rw backup-path-index? uint8
| +--rw sid-list
| +--rw out-sid* [sid]
| +--rw sid srv6-types:srv6-sid
+--rw end-x_psp_usp
| +--rw protected? boolean
| +--rw paths
| +--rw path* [path-index]
| +--rw path-index uint8
| +--rw interface? if:interface-ref
| +--rw next-hop? inet:ipv6-address
| +--rw table? srv6-types:table-id
| +--rw weight? uint32
| +--rw role? enumeration
| +--rw backup-path-index? uint8
| +--rw sid-list
| +--rw out-sid* [sid]
| +--rw sid srv6-types:srv6-sid
+--rw end-x_usd
| +--rw protected? boolean
| +--rw paths
| +--rw path* [path-index]
| +--rw path-index uint8
| +--rw interface? if:interface-ref
| +--rw next-hop? inet:ipv6-address
| +--rw table? srv6-types:table-id
| +--rw weight? uint32
| +--rw role? enumeration
| +--rw backup-path-index? uint8
| +--rw sid-list
| +--rw out-sid* [sid]
| +--rw sid srv6-types:srv6-sid
+--rw end-x_psp_usd
| +--rw protected? boolean
| +--rw paths
| +--rw path* [path-index]
| +--rw path-index uint8
| +--rw interface? if:interface-ref
| +--rw next-hop? inet:ipv6-address
| +--rw table? srv6-types:table-id
| +--rw weight? uint32
| +--rw role? enumeration
| +--rw backup-path-index? uint8
| +--rw sid-list
| +--rw out-sid* [sid]
| +--rw sid srv6-types:srv6-sid
+--rw end-x_usp_usd
| +--rw protected? boolean
| +--rw paths
| +--rw path* [path-index]
| +--rw path-index uint8
| +--rw interface? if:interface-ref
| +--rw next-hop? inet:ipv6-address
| +--rw table? srv6-types:table-id
| +--rw weight? uint32
| +--rw role? enumeration
| +--rw backup-path-index? uint8
| +--rw sid-list
| +--rw out-sid* [sid]
| +--rw sid srv6-types:srv6-sid
+--rw end-x_psp_usp_usd
| +--rw protected? boolean
| +--rw paths
| +--rw path* [path-index]
| +--rw path-index uint8
| +--rw interface? if:interface-ref
| +--rw next-hop? inet:ipv6-address
| +--rw table? srv6-types:table-id
| +--rw weight? uint32
| +--rw role? enumeration
| +--rw backup-path-index? uint8
| +--rw sid-list
| +--rw out-sid* [sid]
| +--rw sid srv6-types:srv6-sid
+--rw end-b6-encaps
| +--rw policy-name string
| +--rw source-address inet:ipv6-address
| +--rw paths
| +--rw path* [path-index]
| +--rw path-index uint8
| +--rw interface? if:interface-ref
| +--rw next-hop? inet:ipv6-address
| +--rw table? srv6-types:table-id
| +--rw weight? uint32
| +--rw role? enumeration
| +--rw backup-path-index? uint8
| +--rw sid-list
| +--rw out-sid* [sid]
| +--rw sid srv6-types:srv6-sid
+--rw end-bm
| +--rw policy-name string
| +--rw paths
| +--rw path* [path-index]
| +--rw path-index uint8
| +--rw interface? if:interface-ref
| +--rw next-hop? inet:ip-address
| +--rw weight? uint32
| +--rw role? enumeration
| +--rw backup-path-index? uint8
| +--rw sid-list
| +--rw out-sid* [sid]
| +--rw sid srv6-types:srv6-sid
+--rw end-dx6
| +--rw paths
| +--rw path* [path-index]
| +--rw path-index uint8
| +--rw interface? if:interface-ref
| +--rw next-hop? inet:ipv6-address
| +--rw table? srv6-types:table-id
| +--rw weight? uint32
| +--rw role? enumeration
| +--rw backup-path-index? uint8
| +--rw sid-list
| +--rw out-sid* [sid]
| +--rw sid srv6-types:srv6-sid
+--rw end-dx4
| +--rw paths
| +--rw path* [path-index]
| +--rw path-index uint8
| +--rw interface? if:interface-ref
| +--rw next-hop? inet:ipv4-address
| +--rw table? srv6-types:table-id
| +--rw weight? uint32
| +--rw role? enumeration
| +--rw backup-path-index? uint8
| +--rw sid-list
| +--rw out-sid* [sid]
| +--rw sid srv6-types:srv6-sid
+--rw end-dt6
| +--rw lookup-table-ipv6 srv6-types:table-id
+--rw end-dt4
| +--rw lookup-table-ipv4 srv6-types:table-id
+--rw end-dt46
| +--rw lookup-table-ipv4 srv6-types:table-id
| +--rw lookup-table-ipv6 srv6-types:table-id
+--rw end-dx2
| +--rw path
| +--rw l2-interface if:interface-ref
+--rw end-dx2v
| +--rw lookup-table-vlan srv6-types:table-id
+--rw end-dt2u
| +--rw lookup-table-mac srv6-types:table-id
+--rw end-dt2m
+--rw flooding-table srv6-types:table-id
+--rw paths
+--rw path* [path-index]
+--rw path-index uint8
+--rw l2-interface? if:interface-ref
As per NMDA model, the state related to configuration items specified in above section Section 3.4.1 can be retrieved from the same tree. The state regarding the local-SIDs created by SRv6-static model can be obtained using the state model of SRv6-base. Hence, there is no additional state identified at this time for SRv6-static.¶
None.¶
Following are the items that will be addressed in next revisions:¶
Following are actual YANG definition for SRv6 modules defined earlier in the document.¶
This YANG module imports types defined in [RFC6991].¶
Moreover, the module models behaviors defined in [RFC8986], [I-D.ietf-spring-sr-service-programming], and [RFC9433].¶
<CODE BEGINS> file "ietf-srv6-types@2022-01-14.yang"
// RFC Editor: replace the above date with the date of
// publication and remove this note.
module ietf-srv6-types {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-srv6-types";
prefix srv6-types;
import ietf-inet-types {
prefix inet;
reference "RFC 6991: Common YANG Data Types";
}
organization
"IETF SPRING Working Group";
contact
"WG Web: <http://tools.ietf.org/wg/spring/>
WG List: <mailto:spring@ietf.org>
Editor: Kamran Raza
<mailto:skraza@cisco.com>
Editor: Jaganbabu Rajamanickam
<maito:jrajaman@cisco.com>
Editor: Xufeng Liu
<mailto:xufeng.liu.ietf@gmail.com>
Editor: Zhibo Hu
<mailto:huzhibo@huawei.com>
Editor: Iftekhar Hussain
<mailto:IHussain@infinera.com>
Editor: Himanshu Shah
<mailto:hshah@ciena.com>
Editor: Daniel Voyer
<mailto:daniel.voyer@bell.ca>
Editor: Hani Elmalky
<mailto:helmalky@google.com>
Editor: Satoru Matsushima
<mailto:satoru.matsushima@gmail.com>
Editor: Katsuhiro Horiba
<mailto:katsuhiro.horiba@g.softbank.co.jp>
Editor: Ahmed AbdelSalam
<mailto:ahabdels@cisco.com>
";
description
"This YANG module defines the essential types for the
management of Segment-Routing with IPv6 dataplane (SRv6).
Copyright (c) 2018 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX; see the
RFC itself for full legal notices.";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
revision 2024-03-04 {
description
"Renamed some of End identities";
reference
"RFC XXXX: YANG Data Model for SRv6";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
}
revision 2022-01-14 {
description
"Alignment with SRv6 net-pgm rev16";
reference
"RFC XXXX: YANG Data Model for SRv6";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
}
revision 2019-10-30 {
description
"Renaming of some types";
reference
"RFC XXXX: YANG Data Model for SRv6";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
}
revision 2019-07-08 {
description
"Alignment with latest SRv6 network programming";
reference
"RFC XXXX: YANG Data Model for SRv6";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
}
revision 2018-10-22 {
description
"Initial revision.";
reference
"RFC XXXX: YANG Data Model for SRv6";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
}
identity srv6-endpoint-type {
description
"Base identity from which specific SRv6 Endpoint types are
derived.";
}
/* Endpoints defined under draft-ietf-spring-
* srv6-network-programming */
identity End {
base srv6-endpoint-type;
description
"End function (variant: no PSP, no USP).";
reference
"RFC 8986";
}
identity End_PSP {
base srv6-endpoint-type;
description
"End function (variant: PSP only).";
reference
"RFC 8986";
}
identity End_USP {
base srv6-endpoint-type;
description
"End function (variant: USP only).";
reference
"RFC 8986";
}
identity End_PSP_USP {
base srv6-endpoint-type;
description
"End function (variant: PSP and USP).";
reference
"RFC 8986";
}
identity End.X {
base srv6-endpoint-type;
description
"Endpoint with cross-connect to an array
of layer-3 adjacencies (variant: no PSP, no USP).";
reference
"RFC 8986";
}
identity End.X_PSP {
base srv6-endpoint-type;
description
"Endpoint with cross-connect to an array
of layer-3 adjacencies (variant: PSP only).";
reference
"RFC 8986";
}
identity End.X_USP {
base srv6-endpoint-type;
description
"Endpoint with cross-connect to an array
of layer-3 adjacencies (variant: USP only).";
reference
"RFC 8986";
}
identity End.X_PSP_USP {
base srv6-endpoint-type;
description
"Endpoint with cross-connect to an array
of layer-3 adjacencies (variant: PSP and USP).";
reference
"RFC 8986";
}
identity End.T {
base srv6-endpoint-type;
description
"Endpoint with specific IPv6 table lookup
(variant: no PSP, no USP).";
reference
"RFC 8986";
}
identity End.T_PSP {
base srv6-endpoint-type;
description
"Endpoint with specific IPv6 table lookup
(variant: PSP only).";
reference
"RFC 8986";
}
identity End.T_USP {
base srv6-endpoint-type;
description
"Endpoint with specific IPv6 table lookup
(variant: USP only).";
reference
"RFC 8986";
}
identity End.T_PSP_USP {
base srv6-endpoint-type;
description
"Endpoint with specific IPv6 table lookup
(variant: PSP and USP).";
reference
"RFC 8986";
}
identity End.B6.Encaps {
base srv6-endpoint-type;
description
"Endpoint bound to an SRv6 Policy
where the SRv6 Policy also includes an
IPv6 Source Address A.";
reference
"RFC 8986";
}
identity End.BM {
base srv6-endpoint-type;
description
"Endpoint bound to an SR-MPLS Policy";
reference
"RFC 8986";
}
identity End.DX6 {
base srv6-endpoint-type;
description
"Endpoint with decapsulation and cross-connect
to an array of IPv6 adjacencies";
reference
"RFC 8986";
}
identity End.DX4 {
base srv6-endpoint-type;
description
"Endpoint with decapsulation and cross-connect
to an array of IPv4 adjacencies";
reference
"RFC 8986";
}
identity End.DT6 {
base srv6-endpoint-type;
description
"Endpoint with decapsulation and specific
IPv6 table lookup";
reference
"RFC 8986";
}
identity End.DT4 {
base srv6-endpoint-type;
description
"Endpoint with decapsulation and specific
IPv4 table lookup";
reference
"RFC 8986";
}
identity End.DT46 {
base srv6-endpoint-type;
description
"Endpoint with decapsulation and specific IP
(IPv4 or IPv6) table lookup";
reference
"RFC 8986";
}
identity End.DX2 {
base srv6-endpoint-type;
description
"Endpoint with decapsulation and Layer-2
cross-connect to an L2 interface";
reference
"RFC 8986";
}
identity End.DX2V {
base srv6-endpoint-type;
description
"Endpoint with decapsulation and specific
VLAN L2 table lookup";
reference
"RFC 8986";
}
identity End.DT2U {
base srv6-endpoint-type;
description
"Endpoint with decapsulation and specific
unicast MAC L2 table lookup";
reference
"RFC 8986";
}
identity End.DT2M {
base srv6-endpoint-type;
description
"Endpoint with decapsulation and specific L2 table
flooding";
reference
"RFC 8986";
}
identity End.B6.Encaps.Red {
base srv6-endpoint-type;
description
"This is a reduced encap variation of the End.B6.Encap
behavior.";
reference
"RFC 8986";
}
identity End_USD {
base srv6-endpoint-type;
description
"End function (variant: USD).";
reference
"RFC 8986";
}
identity End_PSP_USD {
base srv6-endpoint-type;
description
"End function (variant: PSP and USD).";
reference
"RFC 8986";
}
identity End_USP_USD {
base srv6-endpoint-type;
description
"End function (variant: USP and USD).";
reference
"RFC 8986";
}
identity End_PSP_USP_USD {
base srv6-endpoint-type;
description
"End function (variant: PSP and USP and USD).";
reference
"RFC 8986";
}
identity End.X_USD {
base srv6-endpoint-type;
description
"Endpoint with cross-connect to an array
of layer-3 adjacencies (variant: USD).";
reference
"RFC 8986";
}
identity End.X_PSP_USD {
base srv6-endpoint-type;
description
"Endpoint with cross-connect to an array
of layer-3 adjacencies (variant: PSP and USD).";
reference
"RFC 8986";
}
identity End.X_USP_USD {
base srv6-endpoint-type;
description
"Endpoint with cross-connect to an array
of layer-3 adjacencies (variant: USP and USD).";
reference
"RFC 8986";
}
identity End.X_PSP_USP_USD {
base srv6-endpoint-type;
description
"Endpoint with cross-connect to an array
of layer-3 adjacencies (variant: PSP and USP and USD).";
reference
"RFC 8986";
}
identity End.T_USD {
base srv6-endpoint-type;
description
"Endpoint with decapsulation and Layer-2
cross-connect to an L2 interface";
reference
"RFC 8986";
}
identity End.T_PSP_USD {
base srv6-endpoint-type;
description
"Endpoint with specific IPv6 table lookup
(variant: PSP and USD).";
reference
"RFC 8986";
}
identity End.T_USP_USD {
base srv6-endpoint-type;
description
"Endpoint with specific IPv6 table lookup
(variant: USP and USD).";
reference
"RFC 8986";
}
identity End.T_PSP_USP_USD {
base srv6-endpoint-type;
description
"Endpoint with specific IPv6 table lookup
(variant: PSP and USP and USD).";
reference
"RFC 8986";
}
/* Endpoints defined under draft-ietf-spring-sr-service-programming */
identity End.AN {
base srv6-endpoint-type;
description
"Service-Chaining SR Aware function (native)";
reference
"draft-ietf-spring-sr-service-programming-05";
// RFC Editor: replace with actual RFC number and remove this note
}
identity End.AS {
base srv6-endpoint-type;
description
"Service-Chaining Static proxy";
reference
"draft-ietf-spring-sr-service-programming-05";
// RFC Editor: replace with actual RFC number and remove this note
}
identity End.AD {
base srv6-endpoint-type;
description
"Service-Chaining Dynamic proxy";
reference
"draft-ietf-spring-sr-service-programming-05";
// RFC Editor: replace with actual RFC number and remove this note
}
identity End.AM {
base srv6-endpoint-type;
description
"Service-Chaining Masquerading SR proxy";
reference
"draft-ietf-spring-sr-service-programming-05";
// RFC Editor: replace with actual RFC number and remove this note
}
identity End.AM_NAT {
base srv6-endpoint-type;
description
"Service-Chaining Masquerading SR proxy with NAT";
reference
"draft-ietf-spring-sr-service-programming-05";
// RFC Editor: replace with actual RFC number and remove this note
}
identity End.AM_CACHE {
base srv6-endpoint-type;
description
"Service-Chaining Masquerading SR proxy with Caching";
reference
"draft-ietf-spring-sr-service-programming-05";
// RFC Editor: replace with actual RFC number and remove this note
}
identity End.AM_NAT_CACHE {
base srv6-endpoint-type;
description
"Service-Chaining Masquerading SR proxy with NAT and Caching";
reference
"draft-ietf-spring-sr-service-programming-05";
// RFC Editor: replace with actual RFC number and remove this note
}
/* Endpoints defined under RFC 9433 */
identity End.MAP {
base srv6-endpoint-type;
description
"DMM End.MAP";
reference
"RFC 9433";
}
identity End.Limit {
base srv6-endpoint-type;
description
"DMM End.Limit";
reference
"RFC 9433";
}
identity End.M.GTP6.D {
base srv6-endpoint-type;
description
"DMM End.M.GTP6.D";
reference
"RFC 9433";
}
identity End.M.GTP6.Di {
base srv6-endpoint-type;
description
"DMM End.M.GTP6.Di";
reference
"RFC 9433";
}
identity End.M.GTP6.E {
base srv6-endpoint-type;
description
"DMM End.M.GTP6.E";
reference
"RFC 9433";
}
identity End.M.GTP4.E {
base srv6-endpoint-type;
description
"DMM End.M.GTP4.E";
reference
"RFC 9433";
}
/* DMM end */
identity srv6-headend-type {
description
"Base identity from which SRv6 headend rule types are derived.";
}
identity H.Encaps {
base srv6-headend-type;
description
"Headend rule H.Encaps with encapsulated of an SRv6 policy";
reference
"draft-ietf-spring-srv6-network-programming-16";
// RFC Editor: replace with actual RFC number and remove this note
}
identity H.Encaps.Red {
base srv6-headend-type;
description
"Headend rule H.Encaps.Red with reduced encap of an
SRv6 policy";
reference
"draft-ietf-spring-srv6-network-programming-16";
// RFC Editor: replace with actual RFC number and remove this note
}
identity H.Encaps.L2 {
base srv6-headend-type;
description
"Headend rule H.Encaps.l2 on the received L2 frame";
reference
"draft-ietf-spring-srv6-network-programming-16";
// RFC Editor: replace with actual RFC number and remove this note
}
identity H.Encaps.L2.Red {
base srv6-headend-type;
description
"Headend rule H.Encaps.L2.Red on the received L2 frame";
reference
"draft-ietf-spring-srv6-network-programming-16";
// RFC Editor: replace with actual RFC number and remove this note
}
identity srv6-security-type {
description
"Base identity from which SRv6 Security rule types are
derived.";
}
identity SEC-1 {
base srv6-security-type;
description
"Support an ACL on the external interface that
drops any traffic with SA or DA in the internal SID space.
(aka Security rule SEC-1)";
}
identity SEC-2 {
base srv6-security-type;
description
"Support an ACL that drops any traffic on local SID as DA
from a source SA that does not belong to internal address
or SID space. (aka Security rule SEC-2)";
}
identity srv6-counter-type {
description
"Base identity from which SRv6 counter types are derived.";
}
identity LocalSID {
base srv6-counter-type;
description
"Count packets and bytes traffic that matched that SID and
was processed successfully (aka Counter CNT-1)";
reference
"RFC 8986";
// RFC Editor: replace with actual RFC number and remove this note
}
typedef srv6-sid {
type inet:ipv6-prefix;
description
"This type defines a SID value in SRv6";
}
typedef srv6-func-value {
type uint32;
description
"This is a typedef for SID's FUNC value";
}
typedef srv6-func-value-reserved-type {
type enumeration {
enum invalid { value 0; description "Invalid function value"; }
}
description "SRv6 SID's FUNC Reserved values";
}
typedef srv6-locator-len {
type uint8 {
range "32 .. 96";
}
description
"This type defines an SRv6 locator len with range constraints";
}
typedef srv6-sid-pfxlen {
type uint8 {
range "32 .. 128";
}
default 128;
description
"This type defines a SID prefixlen with range constraints";
}
typedef sid-alloc-type {
type enumeration {
enum Dynamic {
description
"SID allocated dynamically.";
}
enum Explicit {
description
"SID allocated with explicit (static) value";
}
}
description
"Types of sid allocation used.";
}
identity srv6-sid-owner-type {
description
"Base identity from which SID owner types are derived.";
}
identity isis {
base srv6-sid-owner-type;
description "ISIS";
}
identity ospfv3 {
base srv6-sid-owner-type;
description "OSPFv3";
}
identity bgp {
base srv6-sid-owner-type;
description "BGP";
}
identity evpn {
base srv6-sid-owner-type;
description "EVPN";
}
identity sr-policy {
base srv6-sid-owner-type;
description "SR Policy";
}
identity service-function {
base srv6-sid-owner-type;
description "SF";
}
typedef table-id {
type uint32;
description
"Routing/switching/bridging/VLAN Table Id";
}
typedef srv6-status-type {
type enumeration {
enum up { value 1; description "State is Up"; }
enum down { description "State is Down"; }
}
description
"Status type";
}
typedef srv6-nexthop-type {
type enumeration {
enum ipv4 { value 1; description "IPv4 next-hop"; }
enum ipv6 { description "IPv6 next-hop"; }
enum mpls { description "MPLS next-hop"; }
enum l2 { description "L2 next-hop"; }
}
description
"Forwarding Next-hop type";
}
} // module
<CODE ENDS>
This YANG module imports types defined in [RFC6991], [RFC8294], [RFC8343], and [RFC8349].¶
<CODE BEGINS> file "ietf-srv6-base@2022-01-14.yang"
// RFC Editor: replace the above date with the date of
// publication and remove this note.
module ietf-srv6-base {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-srv6-base";
prefix srv6;
import ietf-interfaces {
prefix "if";
reference "RFC 8343: A YANG Data Model for Interface Management";
}
import ietf-inet-types {
prefix inet;
reference "RFC 6991: Common YANG Data Types";
}
import ietf-yang-types {
prefix "yang";
reference "RFC 6991: Common YANG Data Types";
}
import ietf-routing-types {
prefix "rt-types";
reference "RFC 8294: Common YANG Data Types for the Routing Area";
}
import ietf-routing {
prefix "rt";
reference
"RFC 8349: A YANG Data Model for Routing Management
(NMDA version)";
}
import ietf-segment-routing {
prefix sr;
reference "draft-ietf-spring-sr-yang";
}
import ietf-srv6-types {
prefix srv6-types;
reference "RFC XXXX: YANG Data Model for SRv6";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
}
organization
"IETF SPRING Working Group";
contact
"WG Web: <http://tools.ietf.org/wg/spring/>
WG List: <mailto:spring@ietf.org>
Editor: Kamran Raza
<mailto:skraza@cisco.com>
Editor: Jaganbabu Rajamanickam
<maito:jrajaman@cisco.com>
Editor: Xufeng Liu
<mailto:Xufeng_Liu@jabil.com>
Editor: Zhibo Hu
<mailto:huzhibo@huawei.com>
Editor: Iftekhar Hussain
<mailto:IHussain@infinera.com>
Editor: Himanshu Shah
<mailto:hshah@ciena.com>
Editor: Daniel Voyer
<mailto:daniel.voyer@bell.ca>
Editor: Hani Elmalky
<mailto:helmalky@google.com>
Editor: Satoru Matsushima
<mailto:satoru.matsushima@gmail.com>
Editor: Katsuhiro Horiba
<mailto:katsuhiro.horiba@g.softbank.co.jp>
Editor: Ahmed AbdelSalam
<mailto:ahabdels@cisco.com>
";
description
"This YANG module defines the essential elements for the
management of Segment-Routing with IPv6 dataplane (SRv6).
Copyright (c) 2017 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX; see the
RFC itself for full legal notices.";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
revision 2022-01-14 {
description
"Alignment with SRv6 network programming rev16";
reference
"RFC XXXX: YANG Data Model for SRv6";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
}
revision 2019-10-30 {
description
"Alignment with SRv6 network programming";
reference
"RFC XXXX: YANG Data Model for SRv6";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
}
revision 2019-07-08 {
description
"Alignment with SRv6 network programming";
reference
"RFC XXXX: YANG Data Model for SRv6";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
}
revision 2018-10-22 {
description
"Initial revision.";
reference
"RFC XXXX: YANG Data Model for SRv6";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
}
/*
* Common
*/
grouping path-attrs-cmn {
description
"Path properties -common for v4/v6";
leaf weight {
type uint32;
description
"This value is used to compute a loadshare to perform un-equal
load balancing when multiple outgoing path(s) are specified. A
share is computed as a ratio of this number to the total under
all configured path(s).";
}
leaf role {
type enumeration {
enum PRIMARY { description "Path as primary traffic carrying"; }
enum BACKUP { description "Path acts as a backup"; }
enum PRIMARY_AND_BACKUP {
description "Path acts as primary and backup simultaneously"; }
}
description "The path role";
}
leaf backup-path-index {
type uint8;
description "Index of the protecting (backup) path";
}
}
grouping path-out-sids {
description "Grouping for path's SID stack";
list out-sid {
key "sid";
description "Out SID";
leaf sid {
type srv6-types:srv6-sid;
description "SID value";
}
}
}
grouping path-out-labels {
description "Grouping for path's label stack";
list out-label {
key "label";
description "Out label";
leaf label {
type rt-types:mpls-label;
description "Label value";
}
}
}
/*
* Config and State
*/
grouping srv6-encap {
description "Grouping for encap param config.";
container encapsulation {
description "Configure encapsulation related parameters";
leaf source-address {
type inet:ipv6-address;
description "Specify a source address (for T.Encap).
The address must locally exists and be routable";
}
container hop-limit {
description "Configure IPv6 header's Hop-limit options";
leaf value {
type uint8;
default 64;
description "Set encapsulating outer IPv6 header's Hoplimit
field to specified value when doing
encapsulation";
}
leaf propagate {
type boolean;
default false;
description "IP TTL/Hop-limit propagation from encapsulated
packet to encapsulating outer IPv6 header's
Hoplimit field. When configured on decapsulation
side, this refers to propagating Hop-limit from
outer IPv6 header to inner header after decap";
}
}
container traffic-class {
description "Configure IPv6 header's Traffic-class options";
leaf value {
type uint8;
default 0;
description "Set encapsulating outer IPv6 header's
Traffic-class field to specified value when
doing encapsulation";
}
leaf propagate {
type boolean;
default false;
description "Propagate (or map) Traffic-class/CoS/PCP from
the incoming packet or L2 Ethernet frame being
encapsulated to the encapsulating IPv6 header's
Traffic-class field.";
}
}
}
}
grouping srv6-locator-state {
description "SRv6 grouping Locator state";
leaf operational-status {
type srv6-types:srv6-status-type;
config false;
description "Indicates whether locator state is UP";
}
leaf is-in-address-conflict {
type boolean;
config false;
description "Indicates whether locator address conflicts with
some other IPv6 address on the box";
}
}
grouping srv6-locators {
description "SRv6 locator grouping";
container locators {
description "SRv6 locators";
list locator {
key "name";
description "Configure a SRv6 locator";
leaf name {
type string;
description "Locator name";
}
leaf enable {
type boolean;
default false;
description "Enable a SRv6 locator";
}
container prefix {
description "Specify locator prefix value";
leaf address {
type inet:ipv6-address;
mandatory true;
description "IPv6 address";
}
leaf length {
type srv6-types:srv6-locator-len;
mandatory true;
description "Locator (prefix) length";
}
}
leaf algorithm {
type uint32 {
range "128..255";
}
description "Algorithm Id (for Flex-Algo)";
}
leaf anycast {
type boolean;
default false;
description "Set to true if locator is an Anycast locator";
}
uses srv6-locator-state;
}
}
}
grouping srv6-stats-in {
description "Grouping for inbound stats";
leaf in-pkts {
type yang:counter64;
description
"A cumulative counter of the total number of packets
received";
}
leaf in-octets {
type yang:counter64;
description
"A cumulative counter of the total bytes received.";
}
}
grouping srv6-stats-out {
description "Grouping for inbound stats";
leaf out-pkts {
type yang:counter64;
description
"A cumulative counter of the total number of packets
transmitted";
}
leaf out-octets {
type yang:counter64;
description
"A cumulative counter of the total bytes transmitted.";
}
}
grouping path-out-sids-choice {
description "Grouping for Out-SID choices";
choice encap-type {
description "Out-SID encap-based choice";
case srv6 {
uses path-out-sids;
}
case mpls {
uses path-out-labels;
}
}
}
grouping local-sid-fwd-state {
description "SRv6 local-SID forwarding state grouping";
container forwarding {
description "SRv6 local-SID forwarding state";
leaf is-installed {
type boolean;
description "Indicates whether SID is installed in forwarding";
}
leaf next-hop-type {
type srv6-types:srv6-nexthop-type;
description "Forwarding next-hop types";
}
container paths {
when "../is-installed = 'true'" {
description "This container is valid only when the
local-SID is installed in forwarding";
}
list path {
key path-index;
description "The list of paths associated with the SID";
leaf path-index {
type uint8;
description "Index of the path";
}
container l2 {
when "../../../next-hop-type = 'l2'" {
description "This container is valid only for L2 type
of NHs";
}
leaf interface {
type if:interface-ref;
description "The outgoing Layer2 interface";
}
description "L2 information";
}
container l3 {
when "../../../next-hop-type != 'l2'" {
description "This container is valid only for L3 type
of NHs";
}
leaf interface {
type if:interface-ref;
description "The outgoing Layer3 interface";
}
leaf next-hop {
type inet:ip-address;
description "The IP address of the next-hop";
}
uses path-attrs-cmn;
description "L3 information";
}
uses path-out-sids-choice;
}
description "Forwarding paths";
}
}
}
grouping srv6-state-sid {
description "SRv6 SID state grouping";
container local-sids {
config false;
description "Local-SID state";
container counters {
description "SRv6 counters";
container cnt-3 {
description "Counts SRv6 traffic received/dropped on local
prefix not instantiated as local-SID";
uses srv6-stats-in;
}
}
list local-sid {
key "sid";
description "Per-localSID Counters";
leaf sid {
type srv6-types:srv6-sid;
description "Local SID value";
}
uses srv6-locator;
leaf is-reserved {
type boolean;
description "Set to true if SID comes from reserved pool";
}
leaf end-behavior-type {
type identityref {
base srv6-types:srv6-endpoint-type;
}
description "Type of SRv6 end behavior.";
}
leaf alloc-type {
type srv6-types:sid-alloc-type;
description
"Type of sid allocation.";
}
list owner {
key "type instance";
description "SID Owner clients";
leaf type {
type identityref {
base srv6-types:srv6-sid-owner-type;
}
description "SID owner/client type";
}
leaf instance {
type string;
description "Client instance";
}
leaf is-winner {
type boolean;
description "Is this client/owner the winning in terms of
forwarding";
}
}
uses local-sid-fwd-state;
container counters {
description "SRv6 per local-SID counters";
container cnt-1 {
description "Counts SRv6 traffic received on local-SID
prefix and processed successfully";
uses srv6-stats-in;
}
}
}
}
}
grouping srv6-support-ends {
description "SRv6 End behavior support grouping";
list end-behavior {
key "type";
description "End behavior support";
leaf type {
type identityref {
base srv6-types:srv6-endpoint-type;
}
description "End behavior (End*) type";
}
leaf supported {
type boolean;
mandatory true;
description "True if supported";
}
}
}
grouping srv6-support-headends {
description "SRv6 Headend behavior support grouping";
list headend-behavior {
key "type";
description "Headend behavior support";
leaf type {
type identityref {
base srv6-types:srv6-headend-type;
}
description "Headend behavior (H*) type";
}
leaf supported {
type boolean;
mandatory true;
description "True if supported";
}
}
}
grouping srv6-msd-signaled {
description "SRv6 MSD signaled parameter support grouping";
container msd {
description "SRv6 signaled MSD parameter support";
leaf max-sl {
type uint8;
description "Maximum value of the SL field in the SRH of
a received packet before applying the Endpoint behavior
associated with a SID";
}
leaf max-end-pop {
type uint8;
description "Maximum number of SIDs in the top SRH in an
SRH stack to which the router can apply
PSP or USP flavors";
}
leaf max-h_encap {
type uint8;
description "Maximum number of SIDs that can be pushed as
part of the H.Encaps* behavior";
}
leaf max-end_d {
type uint8;
description "Maximum number of SIDs in an SRH when applying
End.D* behaviors (e.g. End.X6 and End.DT6)";
}
}
}
grouping srv6-support-security-rules {
description "SRv6 Security rules grouping";
list security-rule {
key "type";
description "Security rule support";
leaf type {
type identityref {
base srv6-types:srv6-security-type;
}
description "Security rule type";
}
leaf supported {
type boolean;
mandatory true;
description "True if supported";
}
}
}
grouping srv6-support-counters {
description "SRv6 Counters grouping";
list counters {
key "type";
description "SRv6 counter support";
leaf type {
type identityref {
base srv6-types:srv6-counter-type;
}
description "Counter type";
}
leaf supported {
type boolean;
mandatory true;
description "True if supported";
}
}
}
grouping srv6-state-capabilities {
description "SRv6 node capabilities grouping";
container node-capabilities {
config false;
description "Node's SRv6 capabilities";
uses srv6-support-ends;
uses srv6-support-headends;
uses srv6-msd-signaled;
uses srv6-support-security-rules;
uses srv6-support-counters;
}
}
augment "/rt:routing/sr:segment-routing" {
description
"This augments Segment Routing (SR) with SRv6.";
container srv6 {
description "Segment Routing with IPv6 dataplane";
/* config */
leaf enable {
type boolean;
default false;
description "Enable SRv6";
}
uses srv6-encap;
uses srv6-locators;
uses srv6-state-capabilities;
uses srv6-state-sid;
}
}
/* Notifications */
grouping srv6-locator {
description
"An absolute reference to an SRv6 locator";
leaf locator {
type leafref {
path "/rt:routing/sr:segment-routing/srv6:srv6/srv6:locators/srv6:locator/srv6:name";
}
description
"Reference to a SRv6 locator.";
}
}
notification srv6-locator-status-event {
description
"Notification event for a change of SRv6 locator operational
status.";
leaf operational-status {
type srv6-types:srv6-status-type;
description "Operational status";
}
uses srv6-locator;
}
notification srv6-sid-collision-event {
description
"Notification event for an SRv6 SID collision - i.e., attempt
to bind an already bound SID to a new context";
leaf sid {
type srv6-types:srv6-sid;
description "SRv6 SID";
}
container existing {
description "Current assignment / bind";
leaf end-behavior-type {
type identityref {
base srv6-types:srv6-endpoint-type;
}
description "End type";
}
// TODO: More
}
container requested {
description "Requested assignment / bind";
leaf end-behavior-type {
type identityref {
base srv6-types:srv6-endpoint-type;
}
description "End type";
}
}
}
} // module
<CODE ENDS>
This YANG module imports types defined in [RFC6991], [RFC8343], and [RFC8349].¶
<CODE BEGINS> file "ietf-srv6-static@2022-01-14.yang"
// RFC Editor: replace the above date with the date of
// publication and remove this note.
module ietf-srv6-static {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-srv6-static";
prefix srv6-static;
import ietf-interfaces {
prefix "if";
reference "RFC 8343: A YANG Data Model for Interface Management";
}
import ietf-inet-types {
prefix inet;
reference "RFC 6991: Common YANG Data Types";
}
import ietf-routing {
prefix "rt";
reference
"RFC 8349: A YANG Data Model for Routing Management (NMDA
version)";
}
import ietf-segment-routing {
prefix sr;
reference "draft-ietf-spring-sr-yang";
}
import ietf-srv6-types {
prefix srv6-types;
reference "RFC XXXX: YANG Data Model for SRv6";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
}
import ietf-srv6-base {
prefix srv6;
reference "RFC XXXX: YANG Data Model for SRv6";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
}
organization
"IETF SPRING Working Group";
contact
"WG Web: <http://tools.ietf.org/wg/spring/>
WG List: <mailto:spring@ietf.org>
Editor: Kamran Raza
<mailto:skraza@cisco.com>
Editor: Jaganbabu Rajamanickam
<maito:jrajaman@cisco.com>
Editor: Xufeng Liu
<mailto:xufeng.liu.ietf@gmail.com>
Editor: Zhibo Hu
<mailto:huzhibo@huawei.com>
Editor: Iftekhar Hussain
<mailto:IHussain@infinera.com>
Editor: Himanshu Shah
<mailto:hshah@ciena.com>
Editor: Daniel Voyer
<mailto:daniel.voyer@bell.ca>
Editor: Hani Elmalky
<mailto:helmalky@google.com>
Editor: Satoru Matsushima
<mailto:satoru.matsushima@gmail.com>
Editor: Katsuhiro Horiba
<mailto:katsuhiro.horiba@g.softbank.co.jp>
Editor: Ahmed AbdelSalam
<mailto:ahabdels@cisco.com>
";
description
"This YANG module defines the essential elements for the
management of Static application for Segment-Routing with
IPv6 dataplane (SRv6).
Copyright (c) 2018 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX; see the
RFC itself for full legal notices.";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
revision 2024-03-04 {
description
"Fixed static yang warnings";
reference
"RFC XXXX: YANG Data Model for SRv6";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
}
revision 2022-01-14 {
description
"Alignment with SRv6 network programming rev16";
reference
"RFC XXXX: YANG Data Model for SRv6";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
}
revision 2019-10-30 {
description
"Extended model for EVPN behaviors";
reference
"RFC XXXX: YANG Data Model for SRv6";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
}
revision 2019-07-08 {
description
"Alignment with SRv6 network programming";
reference
"RFC XXXX: YANG Data Model for SRv6";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
}
revision 2018-10-22 {
description
"Initial revision.";
reference
"RFC XXXX: YANG Data Model for SRv6";
// RFC Editor: replace XXXX with actual RFC number and remove
// this note
}
/*
* Config and State
*/
grouping path-attrs-v6 {
description
"IPv6 Path properties";
leaf interface {
type if:interface-ref;
description "The outgoing interface";
}
leaf next-hop {
type inet:ipv6-address;
description "The IP address of the next-hop";
}
leaf table {
type srv6-types:table-id;
description "The routing table associated with the next-hop";
}
uses srv6:path-attrs-cmn;
}
grouping path-attrs-v4 {
description
"IPv4 Path properties";
leaf interface {
type if:interface-ref;
description "The outgoing interface";
}
leaf next-hop {
type inet:ipv4-address;
description "The IP address of the next-hop";
}
leaf table {
type srv6-types:table-id;
description "The routing table associated with the next-hop";
}
uses srv6:path-attrs-cmn;
}
grouping path-attrs-mpls {
description
"MPLS Path properties";
leaf interface {
type if:interface-ref;
description "The outgoing interface";
}
leaf next-hop {
type inet:ip-address;
description "The IP address of the next-hop";
}
uses srv6:path-attrs-cmn;
}
grouping multi-paths-v6 {
description "Multipath grouping";
container paths {
description "List of outgoing paths";
list path {
key path-index;
description "The list of paths associated with the SID";
leaf path-index {
type uint8;
description "Index of the path";
}
uses path-attrs-v6;
container sid-list {
description "SID-list associated with the path";
uses srv6:path-out-sids;
}
}
}
}
grouping multi-paths-v4 {
description "Multipath grouping";
container paths {
description "List of outgoing paths";
list path {
key path-index;
description "The list of paths associated with the SID";
leaf path-index {
type uint8;
description "Index of the path";
}
uses path-attrs-v4;
container sid-list {
description "SID-list associated with the path";
uses srv6:path-out-sids;
}
}
}
}
grouping multi-paths-mpls {
description "Multipath grouping";
container paths {
description "List of outgoing paths";
list path {
key path-index;
description "The list of paths associated with the SID";
leaf path-index {
type uint8;
description "Index of the path";
}
uses path-attrs-mpls;
container sid-list {
description "SID-list associated with the path";
uses srv6:path-out-sids;
}
}
}
}
grouping multi-paths-v6-BUM {
description
"Multipath grouping for EVPN bridging BUM use case";
container paths {
description
"List of outgoing paths for flooding";
list path {
key path-index;
description "The list of paths associated with the SID";
leaf path-index {
type uint8;
description "Index of the path";
}
leaf l2-interface {
type if:interface-ref;
description "The outgoing L2 interface for flooding";
}
}
}
}
grouping srv6-sid-config {
description
"Configuration parameters relating to SRv6 sid.";
leaf function {
type srv6-types:srv6-func-value;
description
"SRv6 function value.";
}
leaf end-behavior-type {
type identityref {
base srv6-types:srv6-endpoint-type;
}
mandatory true;
description
"Type of SRv6 end behavior.";
}
container end {
when "../end-behavior-type = 'srv6-types:End'" {
description
"This container is valid only when the user chooses End
behavior (variant: no PSP, no USP).";
}
description
"The Endpoint function is the most basic function.
FIB lookup on updated DA and forward accordingly
to the matched entry.
This is the SRv6 instantiation of a Prefix SID
(variant: no PSP, no USP)";
}
container end_psp {
when "../end-behavior-type = 'srv6-types:End_PSP'" {
description
"This container is valid only when the user chooses End
behavior (variant: PSP only).";
}
description
"The Endpoint function is the most basic function.
FIB lookup on updated DA and forward accordingly
to the matched entry.
This is the SRv6 instantiation of a Prefix SID
(variant: PSP only)";
}
container end_usp {
when "../end-behavior-type = 'srv6-types:End_USP'" {
description
"This container is valid only when the user chooses End
behavior (variant: USP only).";
}
description
"The Endpoint function is the most basic function.
FIB lookup on updated DA and forward accordingly
to the matched entry.
This is the SRv6 instantiation of a Prefix SID
(variant: USP only)";
}
container end_psp_usp {
when "../end-behavior-type = 'srv6-types:End_PSP_USP'" {
description
"This container is valid only when the user chooses End
behavior (variant: PSP/USP).";
}
description
"The Endpoint function is the most basic function.
FIB lookup on updated DA and forward accordingly
to the matched entry.
This is the SRv6 instantiation of a Prefix SID
(variant: PSP/USP)";
}
container end_usd {
when "../end-behavior-type = 'srv6-types:End_USD'" {
description
"This container is valid only when the user chooses End
behavior (variant: USD only).";
}
description
"The Endpoint function is the most basic function.
FIB lookup on updated DA and forward accordingly
to the matched entry.
This is the SRv6 instantiation of a Prefix SID
(variant: USD)";
}
container end_psp_usd {
when "../end-behavior-type = 'srv6-types:End_PSP_USD'" {
description
"This container is valid only when the user chooses End
behavior (variant: PSP/USD).";
}
description
"The Endpoint function is the most basic function.
FIB lookup on updated DA and forward accordingly
to the matched entry.
This is the SRv6 instantiation of a Prefix SID
(variant: PSP/USD)";
}
container end_usp_usd {
when "../end-behavior-type = 'srv6-types:End_USP_USD'" {
description
"This container is valid only when the user chooses End
behavior (variant: USP/USD).";
}
description
"The Endpoint function is the most basic function.
FIB lookup on updated DA and forward accordingly
to the matched entry.
This is the SRv6 instantiation of a Prefix SID
(variant: USP/USD)";
}
container end_psp_usp_usd {
when "../end-behavior-type = 'srv6-types:End_PSP_USP_USD'" {
description
"This container is valid only when the user chooses End
behavior (variant: PSP/USP/USD).";
}
description
"The Endpoint function is the most basic function.
FIB lookup on updated DA and forward accordingly
to the matched entry.
This is the SRv6 instantiation of a Prefix SID
(variant: PSP/USP/USD)";
}
container end-t {
when "../end-behavior-type = 'srv6-types:End.T'" {
description
"This container is valid only when the user chooses
End.T behavior (variant: no PSP, no USP).";
}
description
"Endpoint with specific IPv6 table lookup (variant: no PSP,
no USP).
Lookup the next segment in IPv6 table T
associated with the SID and forward via
the matched table entry.
The End.T is used for multi-table operation
in the core.";
// TODO presence "Mandatory child only if container is present";
leaf lookup-table-ipv6 {
type srv6-types:table-id;
mandatory true;
description
"Table Id for lookup on updated DA (next segment)";
}
}
container end-t_psp {
when "../end-behavior-type = 'srv6-types:End.T_PSP'" {
description
"This container is valid only when the user chooses
End.T behavior (variant: PSP only).";
}
description
"Endpoint with specific IPv6 table lookup (variant: PSP only).
Lookup the next segment in IPv6 table T
associated with the SID and forward via
the matched table entry.
The End.T is used for multi-table operation
in the core.";
// TODO presence "Mandatory child only if container is present";
leaf lookup-table-ipv6 {
type srv6-types:table-id;
mandatory true;
description
"Table Id for lookup on updated DA (next segment)";
}
}
container end-t_usp {
when "../end-behavior-type = 'srv6-types:End.T_USP'" {
description
"This container is valid only when the user chooses
End.T behavior (variant: USP only).";
}
description
"Endpoint with specific IPv6 table lookup (variant: USP only).
Lookup the next segment in IPv6 table T
associated with the SID and forward via
the matched table entry.
The End.T is used for multi-table operation
in the core.";
// TODO presence "Mandatory child only if container is present";
leaf lookup-table-ipv6 {
type srv6-types:table-id;
mandatory true;
description
"Table Id for lookup on updated DA (next segment)";
}
}
container end-t_psp_usp {
when "../end-behavior-type = 'srv6-types:End.T_PSP_USP'" {
description
"This container is valid only when the user chooses
End.T behavior (variant: USP/PSP).";
}
description
"Endpoint with specific IPv6 table lookup (variant: USP/PSP).
Lookup the next segment in IPv6 table T
associated with the SID and forward via
the matched table entry.
The End.T is used for multi-table operation
in the core.";
// TODO presence "Mandatory child only if container is present";
leaf lookup-table-ipv6 {
type srv6-types:table-id;
mandatory true;
description
"Table Id for lookup on updated DA (next segment)";
}
}
container end-t_usd {
when "../end-behavior-type = 'srv6-types:End.T_USD'" {
description
"This container is valid only when the user chooses
End.T behavior (variant: USD only).";
}
description
"Endpoint with specific IPv6 table lookup (variant: USD only).
Lookup the next segment in IPv6 table T
associated with the SID and forward via
the matched table entry.
The End.T is used for multi-table operation
in the core.";
// TODO presence "Mandatory child only if container is present";
leaf lookup-table-ipv6 {
type srv6-types:table-id;
mandatory true;
description
"Table Id for lookup on updated DA (next segment)";
}
}
container end-t_psp_usd {
when "../end-behavior-type = 'srv6-types:End.T_PSP_USD'" {
description
"This container is valid only when the user chooses
End.T behavior (variant: PSP/USD only).";
}
description
"Endpoint with specific IPv6 table lookup (variant: PSP/USD
only).
Lookup the next segment in IPv6 table T
associated with the SID and forward via
the matched table entry.
The End.T is used for multi-table operation
in the core.";
// TODO presence "Mandatory child only if container is present";
leaf lookup-table-ipv6 {
type srv6-types:table-id;
mandatory true;
description
"Table Id for lookup on updated DA (next segment)";
}
}
container end-t_usp_usd {
when "../end-behavior-type = 'srv6-types:End.T_USP_USD'" {
description
"This container is valid only when the user chooses
End.T behavior (variant: USP/USD only).";
}
description
"Endpoint with specific IPv6 table lookup (variant:
USP/USD only).
Lookup the next segment in IPv6 table T
associated with the SID and forward via
the matched table entry.
The End.T is used for multi-table operation
in the core.";
// TODO presence "Mandatory child only if container is present";
leaf lookup-table-ipv6 {
type srv6-types:table-id;
mandatory true;
description
"Table Id for lookup on updated DA (next segment)";
}
}
container end-t_psp_usp_usd {
when "../end-behavior-type = 'srv6-types:End.T_PSP_USP_USD'" {
description
"This container is valid only when the user chooses
End.T behavior (variant: USP only).";
}
description
"Endpoint with specific IPv6 table lookup (variant:
PSP/USP/USD only).
Lookup the next segment in IPv6 table T
associated with the SID and forward via
the matched table entry.
The End.T is used for multi-table operation
in the core.";
// TODO presence "Mandatory child only if container is present";
leaf lookup-table-ipv6 {
type srv6-types:table-id;
mandatory true;
description
"Table Id for lookup on updated DA (next segment)";
}
}
container end-x {
when "../end-behavior-type = 'srv6-types:End.X'" {
description
"This container is valid only when the user chooses
End.X behavior (variant: no USP/PSP)";
}
description
"Endpoint with cross-connect to an array of
layer-3 adjacencies (variant: no USP/PSP).
Forward to layer-3 adjacency bound to the SID S.
The End.X function is required to express any
traffic-engineering policy.";
leaf protected {
type boolean;
default false;
description "Is Adj-SID protected?";
}
uses multi-paths-v6;
}
container end-x_psp {
when "../end-behavior-type = 'srv6-types:End.X_PSP'" {
description
"This container is valid only when the user chooses
End.X behavior (variant: PSP only)";
}
description
"Endpoint with cross-connect to an array of
layer-3 adjacencies (variant: PSP only).
Forward to layer-3 adjacency bound to the SID S.
The End.X function is required to express any
traffic-engineering policy.";
leaf protected {
type boolean;
default false;
description "Is Adj-SID protected?";
}
uses multi-paths-v6;
}
container end-x_usp {
when "../end-behavior-type = 'srv6-types:End.X_USP'" {
description
"This container is valid only when the user chooses
End.X behavior (variant: USP only)";
}
description
"Endpoint with cross-connect to an array of
layer-3 adjacencies (variant: USP only).
Forward to layer-3 adjacency bound to the SID S.
The End.X function is required to express any
traffic-engineering policy.";
leaf protected {
type boolean;
default false;
description "Is Adj-SID protected?";
}
uses multi-paths-v6;
}
container end-x_psp_usp {
when "../end-behavior-type = 'srv6-types:End.X_PSP_USP'" {
description
"This container is valid only when the user chooses
End.X behavior (variant: PSP/USP)";
}
description
"Endpoint with cross-connect to an array of
layer-3 adjacencies (variant: PSP/USP).
Forward to layer-3 adjacency bound to the SID S.
The End.X function is required to express any
traffic-engineering policy.";
leaf protected {
type boolean;
default false;
description "Is Adj-SID protected?";
}
uses multi-paths-v6;
}
container end-x_usd {
when "../end-behavior-type = 'srv6-types:End.X_USD'" {
description
"This container is valid only when the user chooses
End.X behavior (variant: USD only)";
}
description
"Endpoint with cross-connect to an array of
layer-3 adjacencies (variant: PSP/USP).
Forward to layer-3 adjacency bound to the SID S.
The End.X function is required to express any
traffic-engineering policy.";
leaf protected {
type boolean;
default false;
description "Is Adj-SID protected?";
}
uses multi-paths-v6;
}
container end-x_psp_usd {
when "../end-behavior-type = 'srv6-types:End.X_PSP_USD'" {
description
"This container is valid only when the user chooses
End.X behavior (variant: PSP/USD only)";
}
description
"Endpoint with cross-connect to an array of
layer-3 adjacencies (variant: PSP/USP).
Forward to layer-3 adjacency bound to the SID S.
The End.X function is required to express any
traffic-engineering policy.";
leaf protected {
type boolean;
default false;
description "Is Adj-SID protected?";
}
uses multi-paths-v6;
}
container end-x_usp_usd {
when "../end-behavior-type = 'srv6-types:End.X_USP_USD'" {
description
"This container is valid only when the user chooses
End.X behavior (variant: USP/USD only)";
}
description
"Endpoint with cross-connect to an array of
layer-3 adjacencies (variant: PSP/USP).
Forward to layer-3 adjacency bound to the SID S.
The End.X function is required to express any
traffic-engineering policy.";
leaf protected {
type boolean;
default false;
description "Is Adj-SID protected?";
}
uses multi-paths-v6;
}
container end-x_psp_usp_usd {
when "../end-behavior-type = 'srv6-types:End.X_PSP_USP_USD'" {
description
"This container is valid only when the user chooses
End.X behavior (variant: PSP/USP/USD only)";
}
description
"Endpoint with cross-connect to an array of
layer-3 adjacencies (variant: PSP/USP).
Forward to layer-3 adjacency bound to the SID S.
The End.X function is required to express any
traffic-engineering policy.";
leaf protected {
type boolean;
default false;
description "Is Adj-SID protected?";
}
uses multi-paths-v6;
}
container end-b6-encaps {
when "../end-behavior-type = 'srv6-types:End.B6.Encaps' or
../end-behavior-type = 'srv6-types:End.B6.Encaps.Red'" {
description
"This container is valid only when the user chooses
End.B6.Encaps or End.B6.Encaps.Red behavior.";
}
description
"Endpoint bound to an SRv6 Policy.
Insert SRH based on the policy and forward the
packet toward the first hop configured in the policy.
This is the SRv6 instantiation of a Binding SID.
This behavior also adds an outer IPv6 header";
// TODO presence "Mandatory child only if container is present";
leaf policy-name {
type string;
mandatory true;
description "SRv6 policy name.";
}
leaf source-address {
type inet:ipv6-address;
mandatory true;
description
"IPv6 source address for Encap.";
}
uses multi-paths-v6;
}
container end-bm {
when "../end-behavior-type = 'srv6-types:End.BM'" {
description
"This container is valid only when the user chooses
End.BM behavior.";
}
description
"Endpoint bound to an SR-MPLS Policy.
push an MPLS label stack <L1, L2, L3> on the
received packet and forward the according to
Lable L1.
This is an SRv6 instantiation of an SR-MPLS Binding SID.";
// TODO presence "Mandatory child only if container is present";
leaf policy-name {
type string;
mandatory true;
description "SRv6 policy name";
}
uses multi-paths-mpls;
}
container end-dx6 {
when "../end-behavior-type = 'srv6-types:End.DX6'" {
description
"This container is valid only when the user chooses
End.DX6 behavior.";
}
description
"Endpoint with decapsulation and cross-connect to
an array of IPv6 adjacencies. Pop the (outer)
IPv6 header and its extension headers and forward
to layer-3 adjacency bound to the SID S.
The End.DX6 used in the L3VPN use-case.";
uses multi-paths-v6;
// TODO: Backup path of type "Lookup in table"
}
container end-dx4 {
when "../end-behavior-type = 'srv6-types:End.DX4'" {
description
"This container is valid only when the user chooses
End.DX4 behavior.";
}
description
"Endpoint with decapsulation and cross-connect to
an array of IPv4 adjacencies.
Pop the (outer) IPv6 header and its extension
header and forward to layer-3 adjacency bound
to the SID S.
This would be equivalent to the per-CE VPN
label in MPLS.";
uses multi-paths-v4;
// TODO: Backup path of type "Lookup in table"
}
container end-dt6 {
when "../end-behavior-type = 'srv6-types:End.DT6'" {
description
"This container is valid only when the user chooses
End.DT6 behavior.";
}
description
"Endpoint with decapsulation and specific IPv6 table
lookup.
Pop the (outer) IPv6 header and its extension
headers.
Lookup the exposed inner IPv6 DA in IPv6
table T and forward via the matched table entry.
End.DT6 function is used in L3VPN use-case.";
// TODO presence "Mandatory child only if container is present";
leaf lookup-table-ipv6 {
type srv6-types:table-id;
mandatory true;
description "IPv6 table";
}
}
container end-dt4 {
when "../end-behavior-type = 'srv6-types:End.DT4'" {
description
"This container is valid only when the user chooses
End.DT4 behavior.";
}
description
"Endpoint with decapsulation and specific
IPv4 table lookup.
Pop the (outer) IPv6 header and its extension
headers.
Lookup the exposed inner IPv4 DA in IPv4
table T and forward via the matched table entry.
This would be equivalent to the per-VRF VPN label
in MPLS.";
// TODO presence "Mandatory child only if container is present";
leaf lookup-table-ipv4 {
type srv6-types:table-id;
mandatory true;
description "IPv4 table";
}
}
container end-dt46 {
when "../end-behavior-type = 'srv6-types:End.DT46'" {
description
"This container is valid only when the user chooses
End.DT46 behavior.";
}
description
"Endpoint with decapsulation and specific
IP table lookup.
Depending on the protocol type (IPv4 or IPv6)
of the inner ip packet and the specific VRF name
forward the packet.
This would be equivalent to the per-VRF VPN
label in MPLS.";
// TODO presence "Mandatory child only if container is present";
leaf lookup-table-ipv4 {
type srv6-types:table-id;
mandatory true;
description "IPv4 table";
}
leaf lookup-table-ipv6 {
type srv6-types:table-id;
mandatory true;
description "IPv6 table";
}
}
/* EVPN END behavior types */
container end-dx2 {
when "../end-behavior-type = 'srv6-types:End.DX2'" {
description
"This container is valid only when the user chooses
End.DX2 behavior.";
}
description
"This is an Endpoint with decapsulation and Layer-2
cross-connect to OIF.
Pop the (outer) IPv6 header and its extension headers.
Forward the resulting frame via OIF associated to the SID.
The End.DX2 function is the L2VPN/EVPN VPWS use-case.";
container path {
description "Outgoing path";
leaf l2-interface {
type if:interface-ref;
mandatory true;
description "Outgoing L2 interface";
}
}
}
container end-dx2v {
when "../end-behavior-type = 'srv6-types:End.DX2V'" {
description
"This container is valid only when the user chooses
End.DX2V behavior.";
}
description
"Endpoint with decapsulation and specific VLAN
L2 table lookup.
Pop the (outer) IPv6 header and its extension headers.
Lookup the exposed inner VLANs in L2 table T.
Forward via the matched table entry.
The End.DX2V is used for EVPN Flexible cross-connect
use-cases";
leaf lookup-table-vlan {
type srv6-types:table-id;
mandatory true;
description
"VLAN lookup table. There could be multiple
vlan demux tables on the node, where a DX2V SID
points to one vlan table";
}
}
container end-dt2u {
when "../end-behavior-type = 'srv6-types:End.DT2U'" {
description
"This container is valid only when the user chooses
End.DT2U behavior.";
}
description
"Endpoint with decapsulation and specific
unicast L2 MAC table lookup.
Pop the (outer) IPv6 header and its extension headers.
Learn the exposed inner MAC SA in L2 MAC table T.
Lookup the exposed inner MAC DA in L2 MAC table T.
Forward via the matched T entry else to all L2OIF in T.
The End.DT2U is used for EVPN Bridging unicast use cases";
leaf lookup-table-mac {
type srv6-types:table-id;
mandatory true;
description "MAC L2 lookup table";
}
}
container end-dt2m {
when "../end-behavior-type = 'srv6-types:End.DT2M'" {
description
"This container is valid only when the user chooses
End.DT2M behavior.";
}
description
"Endpoint with decapsulation and specific flooding table.
Pop the (outer) IPv6 header and its extension headers.
Learn the exposed inner MAC SA in L2 MAC table T.
Forward on all L2OIF (in the flooding table) excluding the one
identfied by Arg.FE2.
The End.DT2M is used for EVPN Bridging BUM use case with
ESI (Split Horizon) filtering capability.";
leaf flooding-table {
type srv6-types:table-id;
mandatory true;
description "L2 Flooding table (list of OIFs)";
}
uses multi-paths-v6-BUM;
/* TODO - Support for argument Arg.FE2. It is an argument specific
to EVPN ESI filtering and EVPN-ETREE used to exclude specific
OIF (or set of OIFs) from flooding table. */
}
/* End of EVPN END behavior types */
}
grouping srv6-static-cfg {
description
"Grouping configuration and operation for SRv6 sid.";
list sid {
key "function";
description "List of locally instantiated SIDs";
uses srv6-sid-config;
}
}
augment "/rt:routing/sr:segment-routing/srv6:srv6/srv6:locators/srv6:locator" {
description
"This augments locator leaf within SRv6.";
container static {
description "Static SRv6";
/* Local SIDs */
container local-sids {
description
"SRv6-static locally instantiated SIDs";
uses srv6-static-cfg;
/* no state for now; SID state accessible through base model */
}
}
}
} // module
<CODE ENDS>
The YANG module specified in this document defines a schema for data that is designed to be accessed via network management protocols such as NETCONF [RFC6241] or RESTCONF [RFC8040]. The lowest NETCONF layer is the secure transport layer, and the mandatory-to-implement secure transport is Secure Shell (SSH) [RFC6242]. The lowest RESTCONF layer is HTTPS, and the mandatory-to-implement secure transport is TLS [RFC8446].¶
The Network Configuration Access Control Model (NACM) [RFC8341] provides the means to restrict access for particular NETCONF or RESTCONF users to a preconfigured subset of all available NETCONF or RESTCONF protocol operations and content.¶
There are a number of data nodes defined in this YANG module that are writable/creatable/ deletable (i.e., config true, which is the default). These data nodes may be considered sensitive or vulnerable in some network environments. Write operations (e.g., edit-config) to these data nodes without proper protection can have a negative effect on network operations.¶
Some of the readable data nodes in this YANG module may be considered sensitive or vulnerable in some network environments. It is thus important to control read access (e.g., via get, get-config, or notification) to these data nodes.¶
It goes without saying that this specification also inherits the security considerations captured in the SRv6 specification document [RFC8986].¶
This document requests the registration of the following URIs in the IETF "XML registry" [RFC3688]:¶
| URI | Registrant | XML |
|---|---|---|
| urn:ietf:params:xml:ns:yang:ietf-srv6-types | The IESG | N/A |
| urn:ietf:params:xml:ns:yang:ietf-srv6-base | The IESG | N/A |
| urn:ietf:params:xml:ns:yang:ietf-srv6-static | The IESG | N/A |
This document requests the registration of the following YANG modules in the "YANG Module Names" registry [RFC6020]:¶
| Name | Namespace | Prefix | Reference |
|---|---|---|---|
| ietf-srv6-types | urn:ietf:params:xml:ns:yang:ietf-srv6-types | srv6-types | This document |
| ietf-srv6-base | urn:ietf:params:xml:ns:yang:ietf-srv6-base | srv6 | This document |
| ietf-srv6-static | urn:ietf:params:xml:ns:yang:ietf-srv6-static | srv6-static | This document |
-- RFC Editor: Replace "This document" with the document RFC number at time of publication, and remove this note.¶
The authors would like to acknowledge Darren Dukes, Les Ginsberg, Ahmed Bashandy, Rajesh Venkateswaran, and Mike Mallin for their review of some of the contents in this draft.¶